Megger DLRO10 10A Low Resistance Ohmmeter 1006-598

Product Code: MEG1006-598

Price

£3520.00 ex. VAT £4224.00 inc. VAT

Available In 3-7 Days

Key Features:

• Accurate results in under three seconds
• Auto current reversal cancels standing emfs
• Fuse protected to 600 V
• NiMH battery reduces weight
• 250 mW power limit (with optional override) to avoid heating the test sample
• Automatically detects continuity in potential and current connections
• Visible warning of high voltages present at the terminals
• Visible warning of current flowing in the test sample
• Multiple operating modes including fully automatic

*Important Calibration Information:
This instrument comes with a ‘manufacturer's certificate of conformity’. It is important to understand that this does NOT constitute a ‘traceable calibration certificate’. A certificate of conformity merely states that the equipment has been designed and produced to meet the requirements of its intended application.
Where calibration of an instrument is possible, we will offer this as a separately purchasable item and may be selected from the drop-down box above. You will be sent a full traceable calibration certificate produced in our laboratory and applied with your details as required.

The Megger DLRO10 bring new standards to low resistance measurement. A fully automatic instrument, selecting the most suitable test current, up to 10 A dc to measure resistance from 0.1 µΩ to 2000 Ω on one of seven ranges.

The DLRO10 is built into a strong, lightweight case that is equally at home in the field or in the laboratory. Light enough to be worn around the neck, they are small enough to be taken into areas which were previously too small to access. DLRO 10 uses a large, bright 4-1/2-digit LED display.

Resistance Ranges			Full Scale Volts		Test Current
Full Scale	Resolution	Accuracy*	Resistive	Inductive	Resistive	Inductive
1.9999 mΩ	0.1 μΩ	±0.2% ±0.2μΩ	20 mV	n/a	10 A	n/a
19.999 mΩ	1 μΩ	±0.2% ±2 μΩ	20 mV	20 mV	1A	1A
199.99 mΩ	10 μΩ	±0.2% ±20 μΩ	20 mV	200 mV	100mA	1A
1.9999 Ω	100μΩ	±0.2% ±0.2 mΩ	20 mV	200 mV	10mA	100mA
19.999 Ω	1 mΩ	±0.2% ±2 mΩ	20 mV	200 mV	1mA	10mA
199.99 Ω	10 mΩ	±0.2% ±20 mΩ	20 mV	200 mV	100 μA	1mA
1999.9 Ω	100 mΩ	±0.2% ±0.2 Ω	200 mV	200 mV	100 μA	100 μA

Megger DLRO10/DLRO10X Technical Specification
	DLRO 10	DLRO 10X
Measurement
Mode	Manual, Auto, Continuous, Inductive	Manual, Auto, Continuous, Inductive, Undirectional
Control	Fully Automatic	Fully Automatic/Manual
Speed	<3s for forward & reverse current and to display average
Display
Measurement	4 1/2 digit seven segment LED
Range and Safety	LED indication	Large backlit LCD
Test Method	Single cycle reversing d.c. ratiometric measurement -average result display
Test Current
Accuracy	±10%
Stability	<10 ppm per second
Maximum Lead Resistance	100 mΩ total for 10 A operation irrespective of battery condition.
Voltmeter Input Impedance	> 200 kΩ
Hum Rejection	Less than 1% ±20 digits additional error with 100 mV peak 50/60 Hz. on the potential leads. Warning will show if hum or noise exceeds this level.
Data Transfer	-	Real Time or from storage via RS232
Storage	-	700 tests
Memo Field	-	Up to 200 characters per test via integral alphanumeric keypad
Battery Capacity	7 Ah NiMH rechargeable
Battery Life	Typical 1000 x 10A Tests Before Recharge
Recharge	Via external 90 V - 260 V 50/60 Hz charger or from 12 to 15 V dc supply
Standard Charging Rate	2.5 hours to 90% capacity, 4 hrs for full charge
Temperature	+5 ºC to +45 ºC (41 ºF to 113 ºF) at full specification -10 ºC to +50 ºC (14 ºF to 122 ºF) at reduced accuracy
Storage Co-Efficient	-30 ºC to +70 ºC (-22 ºF to 158 ºF)
Slow Charging	<0.01% per ºC over range 5 ºC to 40 ºC (<0.006% per ºF from 4 1ºF to 104 ºF)
Humidity (MAX)	+10 ºC to +45 ºC (50 ºF to 113 ºF)
Altitude (MAX)	90% RH @ 40 ºC (104 ºF) non-condensing
Safety	2000 m (6562 ft) to full safety specifications
EMC	In accordance with IEC61010-1 600 V Category III - only when DH6 leads are used. In accordance with IEC61326-1
Dimensions	220 x 100 x 237 mm (8.6 x 4 x 9.5 in)
Weight	2.6 kg (5 3/4 lb.) including battery module
* The accuracy stated assumes forward and reverse measurements. Inductive mode or undirectional mode will introduce an undefined error if an external EMF is present.

UK Mainland	Order by 2pm for Next Day Delivery*
Under £25.00	£4.50
Over £25.00	FREE

UK Highlands & Islands	Order by 2pm for Next Day Delivery*
Under £80.00	£15.00
Over £80.00	FREE